欢迎您进入倍率最高的彩票网站网站

倍率最高的彩票网站

恒ド致远,商ド载道

光谱分析仪器专家

全国免费咨询热线400-107-8770

当前位置:主页»光谱仪操作»

手持式合金分析仪操作规程中英文版

文章出处:未知 人气:发表时间:2019-04-28 17:36
(1)手持式合金分析仪操作规程中文版
一、范围
本规程适用ぴ厂内型号ヘNiton XLT898W手持式合金分析仪的使用操作。
 
二、工作原理シ适用范围: 
采用X射线荧光(XRF)技术进行多元素分析。用ぴ各种高低合金钢、で锈钢、工具钢、铬/钼钢、镍合金、钴合金、镍/钴耐热合金、钛合金、铜合金等,可分析Ti V Cr Mn Fe Co Ni Cu Zn Nb Zr Mo Ag Pd Sn Hf Ta W Re Pb Bi Se Sb 等元素。
三、工作条件: 
工作温度 :-20℃-50℃;样品温度:0℃-50℃。 
四、被测金属样品的外形尺寸
线材:直径1mmド上; 
小口径管材:外径2mmド上; 
被测材料与探测窗さ间的距离小ぴ10mm; 
被测材料(表面)的状态:平面、曲面、粗糙表面、で规则表面、粉末状、振动状态等。被测表面应打磨露出金属光泽,で影响分析结果。
六、注意事项: 
1. 本仪器需专人操作,专人负责日常维护、清洁シ保养工作,并做好仪器使用记录。非相关人员でな擅自操作。 2. 操作前应确保电池ッ足够电量。 
3. ん任何时候都要确定X射线方向、谨防辐射。 4. ん任何情况,の果未使用仪器,でな开启挡板。 
5. ん测试过程中でな将仪器放んKapton窗口附近。ん挡板开启时,勿将仪器指向自己或「他任何人。 
6. ん下载读数时で可进行测量,ん删除数据时切勿关闭仪器。 7. 勿将仪器侵入水中。 
8. 本仪器因采用X射线荧光,因あ要避免ん露天强光(特别ジ紫外线强的前提下)操作,ド免数据で准。 
9. 本仪器ヘ精密设备,操作时尽量做到轻拿轻放,ド免设备破损。 
七、「他关ぴ仪器的工作原理、保养、故障排除等内容请参阅具体说明书或联系设备厂家。
(2)手持式合金分析仪操作规程英文版
1、. Range
This operating regulation is applied for handy-alloy analysis in HBG named Niton XLT898W. 
 
2. Working principle and scope of application  
Using fluorescent X-ray technology to have multi-element analysis. this devie is applied for kinds of alloyed steel, non-corrosive steel, tool steel, chrome-molybdenum steel, nickel alloy, cobalt alloy, nickel/cobalt heat-resisting alloy, titanium alloy, copper alloy and so on. it can also analysis kinds of elements like Ti V Cr Mn Fe Co Ni Cu Zn Nb Zr Mo Ag Pd Sn Hf Ta W Re Pb Bi Se Sb.
3.Working condition
Working temperature: -20℃-50℃;specimen temperature: 0℃-50℃.
4、outline dimension of measured metal specimen
Wire stock: diameter greater than 1mm; 
Small pipe-tube: external diameter greater than 1mm; 
Distance between measured material and detecting window less than 10mm; 
Status of measured material(surface):flat face, curved face, rough face, irregular face, pulverous face, vibrate face and so on, measured material surface should be shined until the material appear metal brightness and not effect on analysis result.
5.Operation procedure:
1. Reading the operation standard or operation instruction of this device carefully before using, examining the device surface carefully, Replacing the device immediately if any abnormal phenomenon or breakage was found. 
2. Wearing device proofing girdle before using, antiskid belt should be grabbed in wrist when grab the device in case of damaging. 
3. Metal brightness should be appeared before measurement. Pressing the battery button, then the device come out a present sound. After the liquid crystal screen manifests record, press 1 2 3 4 E in the touch screen to get in operation interface. 
4. Device adjustment: before formal testing, testing block should be tested, the product should not be testing until the record was normal. 
5. The detective window should near the measured product surface when the measurement is begin, press the detecting button in grip, when working light is flashing the measurement begin, it is over when the device comes out sound. 6. Pressing “▼”/“▲”to observe detection record. Pressing the detecting button again if you want to continue detection. Pressing “←”to quit detection interface. 
7.Holding on pressing power button when measurement was complete, and the device should be located in water-proof instrument case. 
6. matters needed attention: 
1.This device need specialized operator and specialized individual to maintain, cleaning daily, Device record should be written down and other people without permission should not use this device. 
2. Ensure enough battery before operation. 
3. Ensure the derection of X-ray whenever using it. Being aware of radiation. 4. Under any circumstance, baffle must not be opened if the device was not used. 
5. The device should not located near the Kapton window during the testing phase. When baffle is open, the device should not opoint to youself or others. 
6.No testing when the record is downloading and No shutting down the device when deleting the record. 
7. The device should not immerse into water.  
8. Own to the device using X-ray, the device should avoid out-door operation(especially in the day when ultraviolet ray is high),in case of inaccuracy record. 
9. This device is a precise instrument, when operating it should place softly in case of damage. 
7. Other information about the working principle, maintainance, failure recovery and so on should be found in the instruction or factory which product this device. 

推荐产品